Further details
The kit contains the MCT-1 Controller, IR/LIS Receiver, IR Transmitter and Sound Sensor, two mini tripods, two control cables, one trigger cable and a two degree baffle. An additional, separately available Tilt-Sensor Switch will detect movement, adding yet another dimension to this extraordinary trigger system. The abilities of all the sensors are controlled and enhanced by the MCT-1 control unit and it is used to adjust sensitivity and introduce delays in triggering the camera. Single exposure or continuous shooting over given time spans can be chosen. The included trigger cable will operate all cameras with a 2.5mm jack plug remote control connection other models will require adapters (see the accessories tab).
Demonstration Video
Specifications
- Trigger time: Selectable for 5ms (1/200 sec.) to 5 seconds
- Delay time: Short delay 1ms (1/1000 sec.) to 100ms (1/10 sec.) - Long delay 1000ms (1/10 sec.) to 10 seconds
- Trigger modes: Manual, auto 1 shot, auto re-arm
- Focus activation: Manual activation
- Sensor modes: Flash, infra-red beam, sound
- IR beam: Range 20cm to 2m. Wavelength 850 nm. 8 degrees or 2 degrees with focal baffle
- Flash sensor: Range 1 to 1500 lumens. Sensitivity 10 lumens
- Sound response: Microphone sensitivity frequency response 50 to 5000 Hz
- Trigger outputs: x3 open collector (x2 trigger, x1 focus).50 v DC max at 100 milliamps
- Power requirements: x4 AA batteries, high power type, non-rechargeable - AC to low voltage PSU 6 to 9 VDC at 100 milliamps. MP1 Mains power unit recommended (available separately)
- Power consumption: About 40 milliamps. When IR TX module is connected this rises to 80 milliamps
- Size: Controller - (W)19cm x (D)14cm x (H)5cm. Sensors (W)7.5cm x (D)5cm x (H)2.6cm
- Sensor mounting: ¼ inch UNC thread (standard tripod thread)
- Mini tripod height: 8 cm min. 17 cm max
- Weight: MCT-1 Controller 325g. Sensors 43g. Tripods 33g. Kit 950g
- Waterproofing: IP53
- Temperature: 0 to 35 degrees C (operating) -10 to 50 degrees C (non-operating)
- Shock: 10 Newtons
The TriggerSmart kit includes a 3 meter long cable with 2.5 mm jack on each end. This will connect to the following cameras:
CANON
EOS 30, EOS 33, EOS 50E, EOS 300, EOS 300V, EOS 300D, EOS 350D, EOS 3000, EOS 50, EOS 500, EOS 55, EOS 500N, EOS 300X, EOS Kiss, EOS New Kiss, EOS Kiss 7, EOS Kiss III, EOS 7, EOS 7s , EOS 400D, EOS Digital Rebel, EOS Digital, Rebel X, EOS Digital Rebel XSi, EOS KISS X2, EOS 450D, EOS Digital Rebel XTi, Kiss Digital, Kiss Digital N, ELAN 7N, ELAN II, ELAN DATE, ELAN 7, ELAN 7NE, ELAN 7N, ELAN IIE, Rebel 2000, Rebel G, Rebel T2, Rebel Ti, Rebel X, Rebel XS, EOS 1000D, EOS 500D, Rebel T1i, EOS 550D, Rebel T2i, G10, G11, G12, 60D, 600D, Rebel T3i, Kiss X5, 1100D, Rebel T3
PENTAX
K100D, K110D, K10D, *ist DS2, K200D, K20D K7, *ist D, *ist DS, *ist, *ist DL, MZ-6, ZX-L, MZ-, *ist, DL2, K5
SAMSUNG
GX-1L, GX-1S, GX-10, GX-20, NX10, NX100, NX5
CONTAX
645, N, N1, NX, N Digital
Other models will require adapters.